uirt2usb_send: remote not supported

[KShots]

I'm getting the above in my syslog when I attempt to transmit via the usb-uirt2 device.

I'm transmitting with an lircd.conf that successfully receives everything from my remote, but when I try and transmit to my satellite receiver, I just get the above message.

More detail:

Code: Select all

rich@basilisk ~ $ sudo irsend SEND_ONCE dish1 1
Password:
irsend: command failed: SEND_ONCE dish1 1
irsend: transmission failed
rich@basilisk ~ $ sudo tail /var/log/messages
Mar 26 12:34:26 basilisk sudo:     rich : TTY=pts/1 ; PWD=/home/rich ; USER=root ; COMMAND=/usr/local/bin/irsend SEND_ONCE dish1 1
Mar 26 12:34:26 basilisk lircd-0.7.1[11361]: accepted new client on /dev/lircd
Mar 26 12:34:26 basilisk lircd-0.7.1[11361]: uirt2usb_raw: UIRT version 0509 ok
Mar 26 12:34:26 basilisk lircd-0.7.1[11361]: uirt2usb_send: remote not supported
Mar 26 12:34:26 basilisk lircd-0.7.1[11361]: error processing command: SEND_ONCE dish1 1
Mar 26 12:34:26 basilisk lircd-0.7.1[11361]: transmission failed
Mar 26 12:34:26 basilisk lircd-0.7.1[11361]: removed client
Mar 26 12:34:31 basilisk sudo:     rich : TTY=pts/1 ; PWD=/home/rich ; USER=root ; COMMAND=/usr/bin/tail /var/log/messages

irw successfully captures all my remote's buttons, so I know the remote is supported. What gives?

[KShots]

More info:

My directtv remote sends properly, but I don't use a directtv receiver - I use a dish networks receiver. Is this a hardware shortfall?

[stirlitz]

The same with my usb-uirt:
Lirc daemon is configured and is working perfectly when receiving - device reads correctly every button from my remotes but i never succeeded to transmit with it. It always gives me this error:



Jun 2 08:43:04 mc lircd-0.8.0[28091]: accepted new client on /dev/lircd
Jun 2 08:43:05 mc lircd-0.8.0[28091]: uirt2_raw: checksum error
Jun 2 08:43:05 mc lircd-0.8.0[28091]: uirt2: detection of uirt2 failed
Jun 2 08:43:05 mc lircd-0.8.0[28091]: uirt2: trying to detect newer uirt firmware
Jun 2 08:43:05 mc lircd-0.8.0[28091]: uirt2_raw: UIRT version 0905 ok
Jun 2 08:43:05 mc lircd-0.8.0[28091]: uirt2_send: remote not supported
Jun 2 08:43:05 mc lircd-0.8.0[28091]: error processing command: SEND_ONCE sony ON/OFF
Jun 2 08:43:05 mc lircd-0.8.0[28091]: transmission failed
Jun 2 08:43:05 mc lircd-0.8.0[28091]: removed client


This is the result from invoking:

irsend SEND_ONCE sony ON/OFF

I've read all about transmitting in forum but nothing helped with my case.

lircd daemon is started with these options:
/usr/sbin/lircd --driver=uirt2_raw --device=/dev/ttyUSB1

It's configuration file is attached

Please help me with some advice in order to get this device to transmit

Best Regards!

Here is lircd.conf

begin remote

name sony
bits 12
flags SPACE_ENC|CONST_LENGTH
eps 30
aeps 100

header 2383 588
one 1160 588
zero 594 588
post_data_bits 8
post_data 0x92
gap 45026
min_repeat 3
toggle_bit 0

frequency 40000

begin codes
ON/OFF 0xA8B
PAUSE 0x9CB
STOP 0x1CB
UP 0x9EB
DOWN 0x5EB
LEFT 0xDEB
RIGHT 0x3EB
IMENU 0xD8B
1 0x00B
2 0x80B
3 0x40B
4 0xC0B
5 0x20B
6 0xA0B
7 0x60B
8 0xE0B
9 0x10B
0 0x90B
D.TUNNING 0xD0B
RETURN 0x70B
EXECUTE 0xD0B
PBEGIN 0x0CB
PEND 0x8CB
BWD 0xCCB
FWD 0x2CB
PREV 0x64B
NEXT 0xE4B
WHITERIGHT 0x4CB
TITLE 0x58B
DISPLAY 0x2AB
MENU 0xCAB
SIBTITLE 0x46B
SUBTITLE.CHG 0xC6B
AUDIO.CHG 0x26B
SEARCH 0xD2B
CLEAR 0xF0B
end codes

end remote


begin remote

name samsungtv
bits 16
flags SPACE_ENC|CONST_LENGTH
eps 30
aeps 100
frequency 40000

# header 4501 4725
# one 453 1782
# zero 453 707
header 4501 4650
one 550 1670
zero 550 600
ptrail 413
pre_data_bits 16
pre_data 0xE0E0
gap 108500
toggle_bit 0


begin codes
POWER 0x40BF
TV 0xD827
VIDEO 0x807F
-/-- 0xC43B
end codes

end remote

[KShots]

Best I can tell, the USB-UIRT is falsely advertised as a 56Khz transmitter - I can get it to transmit at 38 Khz, but not 56Khz, though with the 56Khz option I can get it to receive in 56K (just not transmit).