Yamaha LPX500 Projector learning probs

[Roscoe62]

Hi!

I've just installed the USB-UIRT, gotten it to show up in Girder as a plugin, and I've even managed to teach it the power on command and this has been successfully tested.

However, when I tried to teach it the different input selection commands I'm failing each time. It's learning it OK, but when I test the command the USBUIRT LED blinks but the projector does not respond.

I tried to do the IR debug and I've got it attached here:

FCB0 5849 156 2C1B 0583 016 1085 0581 016 0583 0585 016 0581 057C 016 0583 0581 016 108C 057E 016 0583 0585 016 1086 0583 016 1089 057C 016 0587 0580 016 1087 0585 016 1089 057C 016 108E 057C 016 0585 0583 016 1087 0585 016 057E 0583 016 057E 0581 016 1089 0585 016 108A 057C 016 0583 0581 016 1089 0581 016 108C 0583 016 0582 0582 016 1085 0585 016 1086 057E 016 0586 0582 016 0580 057E 016 108A 0581 016 0586 057C 016 0587 0580 016 1087 0581 016 0581 0581 016 0582 0585 016 FFFF
030E 5845 156 1611 0580 016 FFFF
075C 5844 156 160F 0583 016 FFFF
075C 5844 156 160E 057C 016 FFFF
075C 5843 156 160F 0583 016 FFFF
075C 5840 156 1611 057C 016 FFFF
075C 5847 156 160C 0583 016 FFFF
075C 583F 156 160F 0583 016 FFFF
075C 5845 156 160C 0583 016 FFFF
075C 5844 156 160E 0585 016 FFFF
075C 5846 156 1607 0581 016 FFFF
075C 5848 156 160C 057E 016 FFFF
075C 5847 156 1611 057C 016 FFFF
075C 5846 156 160C 057E 016 FFFF
075C 5849 156 160E 057C 016 FFFF
075C 5845 156 160B 0580 016 FFFF
075C 5845 156 1611 0580 016 FFFF
075C 5845 156 1609 0580 016 FFFF
075C 5843 156 160F 0583 016 FFFF
075C 5840 156 1611 057C 016 FFFF

Code 1 is listed as follows...

030E41AC56200A0A00A80802A220088AA20000000000000000

and Code 2 is listed as follows...

075C01AC2B00000A00000000000000000000000000

I've tried learning this code 3 or 4 times from various distances and angles but just can't seem to crack it.

I also tried a few other input selection buttons as well but I'm getting the same results.

Are you able to help out at all? Please let me know if you need any further information.

Thanks

Ross

[jrhees]

Ross,

You're almost there! Try learning the button again, but before pressing the remote button, check the box that says 'Force Raw...' in the learn dialog (this is CHECKED by default in future versions of the plugin).

Let me know if that works for you,

-Jon

[Roscoe62]

Jon,

That worked perfectly! Thanks for your help!

Cheers
Ross